123ben
New Member
Hi
I am a very new rcz owner (2 days)
I'm hoping to get some advice from your knowledgeable self's (after lurking in this forum pre purchase)
My car stutters when under hard acceleration 1.6 200. Mainly between 3.5 to 5.5k revers. Only very slightly but noticeable.
I'm covered under the 3 month dealer warrenty and the car will be going back on Monday for repairs.
This evening I had the aa out as it went into limp mode. Total loss of power. But after turning off and on it works fine. But still eml light.
I have the following error codes and it seems like a lot. But the aa guy said it could be one issue that's throwing up multiple codes.
Any ideas
Patrol found the following fault code/s:System : Engine control 1 - 9FG / Motronic MEVD 17.4.2 Status 0948 - Engine oil pump. Error Message : Short to B+. Error static. Status 1385 - Engine oil viscosity. Error Message : Wear/knocking combustion detected. Error sporadic. Status 2337 - Knock control cylinder 3. Error Message : Uncontrolled combustion. Error sporadic. Status 1062 - Variable valve timing. Error Message : Engine power too low. Error sporadic. Status 0945 - Engine oil pump. Error Message : Open circuit/no signal. Error sporadic. Status 1336 - Random/multiple cylinders. Error Message : Misfire detected. Error static. Status 1338 - Ignition failure, cylinder 2. Error Message : Misfire detected. Error static. Status 1340 - Ignition failure, cylinder 4. Error Message : Misfire detected. Error static.Patrol carried out the following special function/s:Special functionsAdjustments / settingsReset adaptation parametersCamshaft adaptionVariable camshaft timing adaptationBasic checks oil and water ok. Member purchased vehicle today, has driven vehicle around 20 miles. When near home EML came on and started running rough. Various fault codes stored, reset adaptation parameters and cleared fault codes. Start vehicle, no unusual noises runs ok and revs normally. No fault codes returned. Advised member take straight back to the garage and have it checked
Thank you
I am a very new rcz owner (2 days)
I'm hoping to get some advice from your knowledgeable self's (after lurking in this forum pre purchase)
My car stutters when under hard acceleration 1.6 200. Mainly between 3.5 to 5.5k revers. Only very slightly but noticeable.
I'm covered under the 3 month dealer warrenty and the car will be going back on Monday for repairs.
This evening I had the aa out as it went into limp mode. Total loss of power. But after turning off and on it works fine. But still eml light.
I have the following error codes and it seems like a lot. But the aa guy said it could be one issue that's throwing up multiple codes.
Any ideas
Patrol found the following fault code/s:System : Engine control 1 - 9FG / Motronic MEVD 17.4.2 Status 0948 - Engine oil pump. Error Message : Short to B+. Error static. Status 1385 - Engine oil viscosity. Error Message : Wear/knocking combustion detected. Error sporadic. Status 2337 - Knock control cylinder 3. Error Message : Uncontrolled combustion. Error sporadic. Status 1062 - Variable valve timing. Error Message : Engine power too low. Error sporadic. Status 0945 - Engine oil pump. Error Message : Open circuit/no signal. Error sporadic. Status 1336 - Random/multiple cylinders. Error Message : Misfire detected. Error static. Status 1338 - Ignition failure, cylinder 2. Error Message : Misfire detected. Error static. Status 1340 - Ignition failure, cylinder 4. Error Message : Misfire detected. Error static.Patrol carried out the following special function/s:Special functionsAdjustments / settingsReset adaptation parametersCamshaft adaptionVariable camshaft timing adaptationBasic checks oil and water ok. Member purchased vehicle today, has driven vehicle around 20 miles. When near home EML came on and started running rough. Various fault codes stored, reset adaptation parameters and cleared fault codes. Start vehicle, no unusual noises runs ok and revs normally. No fault codes returned. Advised member take straight back to the garage and have it checked
Thank you