Menu
What's new
By:
Filters
Peugeot RCZ Forum

Register a free account today to become a member. It's free! Once signed in, you'll be able to participate on this site by adding your own topics and posts, connect with other members through your own private inbox and take part in competitions!

EddieJ's latest activity

  • EddieJ
    EddieJ replied to the thread Turbo.
    the tensioners on the very early cars were only getting torqued at the factory to 60Nm (from memory) and after a bunch of heat cycles...
  • EddieJ
    EddieJ replied to the thread Turbo.
    Go all in on the top and front, valve cover, filter housing to block gaskets as well as the pre mentioned feed pipe. Check the pipe on...
    • 1774988783067.png
  • EddieJ
    EddieJ replied to the thread Turbo.
    Not saying that turbos from eBay are all bad, but you might be better to find a local(ish) respected turbo refurb company. It may work...
  • EddieJ
    EddieJ reacted to apple3337's post in the thread Just like to say... I LOVE MY RCZ :) with Love Love.
    I’ve got a white R here in Oz. I love it. I’ve owned it since 2020. I have no intention of selling it. Inside and out, it’s amazing.
  • EddieJ
    EddieJ reacted to Kenneth's post in the thread Just like to say... I LOVE MY RCZ :) with Like Like.
    I’m not sure about car hacks criticism ls when it came out. The fact honk and here will have been some “its a Peugeot” so they have to...
  • EddieJ
    EddieJ reacted to Griffy's post in the thread Just like to say... I LOVE MY RCZ :) with Like Like.
    Just like to say... I LOVE MY RCZ :) Been saving for a good HDi Gt, ideally in silver, or my dream colour, Moroccan Red, for 2.5yrs...
  • EddieJ
    EddieJ replied to the thread Just like to say... I LOVE MY RCZ :).
    I have my 1.6 156 and am absolutely chuffed with how it drives, handling and performance. Car has a couple of tiny mods to improve it...
  • EddieJ
    EddieJ replied to the thread Peugeot RCZ workshop manual PDF.
    You can download the manual here: LINK
  • EddieJ
    EddieJ reacted to Macro Tsai's post in the thread Coolant sensor with Like Like.
    液位採集器的探棒我以前有過經歷，我拆下採集器後切開外殼，液位標記是焊接在電路板上，焊點長期關閉下打開，重新焊接後安裝回去就好了 。這樣可以免費修復。跟前面分享的影片比較，我的亮點特別長，但功能都一樣。
  • EddieJ
    EddieJ replied to the thread Electrical Gremlin ?.
    Put battery on a long charge, if you have a conditioner charger even better. I would put the most of that down to a discharged battery...
  • EddieJ
    EddieJ replied to the thread New Z, some questions..
    Welcome to the group. Clutch - Some say they do seem hi, but as i have the z and a 308 (same thing), they both have same bit point...
  • EddieJ
    EddieJ reacted to chrismac's post in the thread Heater Matrix with Like Like.
    Success ! Filled the matrix with Radflush (all I had to hand) and left overnight. Flushed and reverse flushed a few times, a few bits...
  • EddieJ
    EddieJ replied to the thread Heater Matrix.
    I used the stuff below to assist when flushing, descaling etc, think I sort of listed out before, but two extension hoses on the matrix...
    • IMG_1396.jpeg
  • EddieJ
    EddieJ replied to the thread THP200 Won't start, F303 Fault: configuration.
    It’s possible one of you engine temperature sensors is faulty, or the split loom for the temp sensors has a wire that is chaffed through...
  • EddieJ
    EddieJ reacted to Dave jc's post in the thread TPMS with Like Like.
    Hi all just a follow up on my last message concerning TPMS. I took my car to Merityre in Basingstoke they checked the sensors also they...
Show older items
Top